|Average 7-day Max. Pavement Design Temp||°C||< 70||ASTM D6373|
|Minimum Pavement Design Temperature||°C||>-28||ASTM D6373|
|Flash Point Temp, T48: Minimum||°C||230||ASTM D92|
|Viscosity Max. Test Temperature||°C||135||ASTM D4402|
|Dynamic Shear, TP5:Min 1.00 kPa test temp@10rad/s||°C||70||ASTM D6373|
|ROLLING THIN FILM OVEN (T240)|
|Mass Loss, Maximum, Percent||%||1.00||ASTM D6|
|Dynamic Shear, TP5:Min 2.20 kPa test temp@10rad/s||°C||70||ASTM D6373|
|PRESSURE AGING VESSEL RESIDUE (PPI)|
|PAV Aging Temperature||–||100/110||–|
|Dynamic Shear, TP5:Max 5000 kPa test temp@10rad/s||°C||25||–|
|Creep Stiffness, TP1:S, Max 300.0MPa, Min0.300 test temp@60s||°C||-18||ASTM D6648|
|Direct Tension, TP3: Failure Strain, Min 1.0% test email@example.com/min||°C||-18||ASTM D6723|
The performance grading of bitumen is based on the evaluation of the material performance and pavement temperatures. In Super-pave grading system, binders are classified according to their Performance in extreme hot and cold temperatures and called as Performance Grade Bitumen. The main purpose of grading and selecting asphalt binder using the Performance Grade system is to make certain that the binder has the appropriate properties for environmental conditions in the field. Performance Grade asphalt binders are selected to meet expected climatic conditions as well as traffic speed and volume adjustments. Therefore, the Performance Grade system uses a common set of tests to measure physical properties of the binder that can be directly related to field performance of the pavement at its service temperatures by engineering principles. Performance grade bitumen generally are mostly applied in paving constructions and reconstructions, sealing of edges, crack sealing, spray applications for the bridge deck, and in both dense-graded and open-graded Hot Mix Asphalt (HMA). PG grades that are well-structured against thermal cracking are PG 58-34, PG 64-22, PG 64-28, and PG 76-22. PG grades that are resistant to rutting are PG 70-22, PG 70-28, PG 76-28, and PG 82-22.PG 58-28 is specifically used in very cold regions.
Performance Grade Bitumen Advantages :
1.Common tests are conducted at a single test temperature which is 25°C in penetration and 60°C in viscosity test, which means that they cannot give any details about how the bitumen would behave in low or high temperatures. Superpave grading indicates a working temperature range of binder and therefore, helps with choosing the best type according to the condition each project demands.
2.Empirical methods such as viscosity and penetration grading systems were developed based on old experiences and can be applicable if those conditions still exist. But,climatic and current traffic conditions are rapidly changing and past experiences can no longer be defining criteria. In the PG system, it is possible to use actual traffic volumeand vehicle speed which represents the duration of loads are applied.
3.Because of the visco-elastic properties of bitumen, the rate of load application and temperature have a great effect on its behavior. Although the behavior of bitumen in lower loading rates corresponds to that of higher temperatures, none of the other grading systems doesn’t take the rate of load into account except for Superpave. While Superpave can be easily used for both unmodified and modified bitumen, conventional methods areused only for unmodified bitumen types.
4.Conventional methods ignore the long-term aging of binders and its behavior. But Superpave takes both long-term aging using with the pressure aging vessel (PAV) and short-term aging using the rolling thin film oven test (RTFOT) into account.
5.Bitumen properties indicated at different temperatures contribute to resistance to the distresses in a different level. Bitumen contributing in a better rutting resistance is measured at maximum pavement temperatures and which leads to a more elastic and stiffer binder. Bitumen contributing to fatigue resistance is the most crucial at average pavement temperatures and it requires asofter bitumen while it still favors an elastic binder. Bitumen contribution to thermal cracking is sensitive atminimum pavement temperatures and it demands a less elastic and soft bitumen.
Safe Handling and Storage:
Use Personal Protective Equipment (PPE’s) when handling (i.e. gloves, eye protectors, etc.)
Maintain safe heating temperatures when using this product
Avoid contact with skin, eyes, and clothing
Avoid breathing vapor, spray, or mists when applying.
Keep drums in a cool, well-ventilated place.
Penetration graded Bitumen PG70-28 is available in 0.6 mm thickness, 180 kg net weight drums, 95 cm height and 45 cm diameter (+/- 3 kg operational tolerance)